McKinney Concrete Lifting logoMcKinney Concrete LiftingMcKinney, TX
Polyurethane Foam Leveling photo

McKinney Concrete Lifting

Polyurethane Foam Leveling in McKinney, TX

Polyurethane foam leveling in McKinney, same-day injection, no messy slurry, free estimates for sunken concrete.

  • 15+ Years local experience
  • 500+ Projects completed
  • Licensed & Insured

Serving McKinney and nearby communities.

Mudjacking used to be the only option for a sunken slab. It's slow, it's messy, and the slurry adds weight the soil underneath may not hold.

Polyurethane foam leveling is the modern fix. McKinney Concrete Lifting injects a lightweight, expanding foam through small drilled holes, and it cures fast enough that most slabs are usable again the same day. On McKinney's expansive clay, that lighter fill matters, since heavy slurry can just sink again as the soil keeps shifting.

What's included

What's Included with Polyurethane Foam Leveling

Typically included: Optional: Customer prep:

  • Drilling small injection holes (roughly dime-sized)
  • Foam injection with real-time lift monitoring
  • Hole patching and cleanup after the pour
  • Soil stabilization resin added to the injection if the void is unusually deep
  • Extra sealant on outdoor joints exposed to rain
  • Move vehicles, planters, or grills off the work area
  • Point out any known underground lines near the slab

How it works

How Our Polyurethane Foam Leveling Process Works

  1. Site visit and slab assessment photo
    Step 1

    Inspection

    Mark the low spots and plan injection points.

  2. Drilling injection holes photo
    Step 2

    Small hole drilling

    Minimal disruption to the surface.

  3. Foam injection photo
    Step 3

    Foam injection

    Expanding foam fills the void under pressure.

  4. Expansion and lift photo
    Step 4

    Lift monitoring

    Technician tracks the rise in real time.

  5. Level check photo
    Step 5

    Level verification

    Straightedge across the slab confirms flush grade.

  6. Hole patching photo
    Step 6

    Patch and seal

    Holes closed, surface cleaned.

Timeline

How long does a Polyurethane Foam Leveling take?

Most single-slab jobs wrap in a single visit.

  1. 01

    Consult and marking

    30 minutes

  2. 02

    Foam injection and lift

    1–3 hours
  3. 03

    Cure before use

    same day

Need a schedule that fits?

Get a Free Estimate

Before & after

Before and After Polyurethane Foam Leveling Results

  • Polyurethane Foam Leveling photo
    Before
  • Polyurethane Foam Leveling photo
    After

FAQs

Polyurethane Foam Leveling FAQs

Is foam better than mudjacking?

For most McKinney homes, yes. Foam is lighter, cures faster, and uses smaller holes. Mudjacking can still make sense on very large commercial slabs where cost per square foot matters more than speed.

How much does foam injection cost compared to mudjacking?

Foam typically runs higher per square foot than mudjacking slurry, but the smaller holes, faster cure, and lighter fill often offset that over the life of the repair.

How long before I can park on a foam-lifted driveway?

Most driveways are drivable the same day, usually within a couple hours once the foam sets.

Can I do foam injection myself?

Foam injection rigs run at controlled pressure and need calibration per job. A miscalibrated pour either underlifts the slab or overlifts one section, so this isn't a rental-store DIY job.

Next step

Get a Polyurethane Foam Leveling Estimate in McKinney

Call McKinney Concrete Lifting at +1 (936) 287-5444 for a free foam leveling estimate. Visit Home to see our full lineup, or go to Contact to send photos ahead of time. See also Concrete Slab Lifting and Driveway Leveling.

Ask about Polyurethane Foam Leveling

Tell us about the project and how to reach you.

Call (936) 287-5444